Line Capacity and Backing: How Much Line Do You Need?
How much line you need on your reel for each fish, how to read line capacity, using mono backing under braid, and top shots.
Nothing is worse than watching the last turns of line disappear from your spool as a big fish keeps running. Line capacity decides how far a fish can run before you lose it. This guide explains how much line you need for each fish, how to read capacity figures, why anglers use backing under braid, and when to add a top shot.
How much line do you need
Think about the first run of your target fish and add a safety margin.
- Bream, snapper, seabass, emperor: 100 to 150 m.
- Bonito, kingfish, queenfish: 150 to 250 m.
- Amberjack, cobia, larger trevally: 200 to 300 m.
- Yellowfin tuna, GT, sailfish: 300 to 500 m.
- Marlin and giant tuna: 600 m or more on large trolling reels.
Depth also matters. If you fish 100 m deep, you need 100 m of line just to reach the bottom before the fish starts running.
Reading line capacity
Reels list capacity like "PE 2 / 300 m" or "20 lb / 200 m". Check:
- The line type: capacity for mono and for braid is different.
- The line strength: a reel that holds 300 m of PE 2 holds much less of PE 4.
Because braid is much thinner than mono, you can fit about two to three times more braid than mono of the same strength. See braid vs mono vs fluorocarbon and spinning reel sizes explained.
What backing is and why it is used
Backing is cheaper line put on the spool first, under the main line.
- To fill the spool: expensive braid fills only part of a deep spool, so cheap mono backing fills the rest.
- To stop braid slipping: braid is slick and can spin around a bare spool. A few metres of mono underneath grips the spool.
- To add emergency capacity for long runs.
Mono backing under braid
- Tie mono to the spool with an arbor knot.
- Wind on enough mono to fill the spool so the braid will finish 2 to 3 mm below the lip.
- Join the braid with a double uni knot or an Albright knot.
- Spool the braid under firm tension.
Tip: to work out how much backing you need, wind the braid on first, then the backing on top until full, and reverse everything onto a second spool.
Top shots
A top shot is a length of mono or fluorocarbon (often 50 to 200 m) on top of braid backing, used mostly for tuna and big game:
- Provides stretch to absorb sudden runs and head shakes.
- Resists abrasion near the boat.
- Is visible less than braid.
Read top shots for tuna.
Do not overfill or underfill
- Overfilled spools throw loose coils and cause wind knots. See how to fix wind knots.
- Underfilled spools cast poorly, because line rubs on the spool lip, and retrieve less line per turn.
Fill to about 2 to 3 mm below the lip on spinning reels and to just below the top of the spool on conventional reels.
Checking line during a fight
If a fish takes more than half your line, consider:
- Chasing it with the boat (on a boat).
- Increasing drag slightly, but carefully. See fishing reel drag explained.
- Pumping and winding to regain line quickly when the fish slows.
Replacing line
Over time you lose line to cut-offs and retying, which reduces capacity. Top up or replace line when the spool level drops noticeably. Read how often to change fishing line.
Mark your backing and main line with a different colour so you know when a fish is getting close to the end.
Identify your catch with ReelScan: snap one photo to get the species, size and safety notes, and earn points. Scan a fish.
Summary
Choose a reel and line that hold enough line for the first run of your target fish, add mono backing under braid to fill the spool and stop slipping, and keep the spool correctly filled. For big pelagics, add a top shot. Spool up correctly with how to spool a spinning reel.