How to Spool a Spinning Reel With Braid or Mono (No Twists)
Step-by-step guide to spooling a spinning reel with braid or monofilament: backing, line direction, tension and how full to fill the spool.
Putting new line on a reel sounds simple, yet a badly spooled reel causes most of the line twist, wind knots, tangles and short casts anglers complain about. Spool it correctly and your line comes off smoothly, casts further and lasts longer. This step-by-step guide shows you how to spool a spinning reel with braid or monofilament, how to add backing, which way the line should come off the filler spool, how much tension to use and how full to fill the spool.
What you need
- Your spinning reel, mounted on a rod (spooling through the first guide keeps tension even).
- The new line on its filler spool.
- Monofilament backing if you are using braid (a few metres up to a quarter of the spool).
- Scissors or line clippers.
- A wet cloth or a cup of water.
- Optional: a pencil or a line spooling tool, and a friend.
Step 1: Choose the right line and amount
Check the line capacity printed on your spool, for example "200 m of 20 lb braid". Decide on the main line type and strength using our fishing line strength guide and the comparison of braid vs monofilament vs fluorocarbon. You rarely need to fill a whole spool with expensive braid; backing fills the rest.
Step 2: Add backing under braid
Braid is slippery and can spin on a smooth spool, so that when you set the hook or a fish runs, the whole load of line rotates on the spool instead of pulling the drag. To stop this:
- Use a reel with a braid-ready spool (rubber band or grip ridge), or
- Tie on monofilament backing first. Even a few metres gives the braid something to grip. Many anglers fill the spool one quarter to one third with cheap mono, then add braid on top.
Connect backing to braid with a double uni knot.
Step 3: Tie the line to the spool
- Open the bail arm. This is essential; if you forget, the line will not wind on properly.
- Pass the line through the first rod guide nearest the reel (the stripper guide).
- Wrap the line around the spool and tie an arbor knot, or use a uni knot around the spool.
- Pull the knot tight, trim the tag end close and close the bail arm.
With braid, a piece of electrical tape over the first wraps on a bare spool also stops slipping.
Step 4: Get the line direction right
This step prevents line twist. A spinning reel's bail lays line onto the spool in one rotational direction. If line comes off the filler spool in the opposite direction, every turn adds a twist.
- Lay the filler spool flat on the floor, label side up.
- Wind 15 to 20 turns onto the reel.
- Lower the rod tip to create slack between the reel and the filler spool and watch the line.
- If the slack line twists into loops, flip the filler spool over so the other side faces up.
- If it hangs straight, keep going.
Monofilament has memory and is most sensitive to direction. Braid does not hold memory in the same way, but correct direction still helps the line lie neatly.
Step 5: Keep firm tension
Line must be wound on tight. Loose line on the spool digs in under load and causes wind knots on the next cast.
- Pinch the line between your thumb and finger in front of the reel, using a wet cloth to protect your skin and cool the line.
- Or run the line through a heavy book, or ask a friend to hold the filler spool on a pencil with light pressure.
- With braid, use firm tension. With mono, moderate tension is enough. Keep it steady.
Wet monofilament as you spool it; dry mono heats up from friction and can be damaged.
Step 6: Fill to the right level
Fill the spool to about 2 to 3 mm (roughly 1/8 inch) below the lip.
- Underfilled: line has to climb over the lip on each cast, which shortens casts noticeably.
- Overfilled: loose loops spring off the spool, causing tangles and wind knots, especially with braid.
Many spools have a marked line to fill to.
Step 7: Finish and settle the line
- Cut the line, leaving enough to reach the rod tip.
- Thread the rod guides and tie on your leader or terminal tackle. For leader connections, see the FG knot.
- On your first trip, make a long cast with no lure and slowly reel back under tension, or tow the line behind a moving boat for a minute. This removes twists and beds the line in under fishing pressure.
How often should you re-spool?
- Monofilament: every season, or sooner if it becomes chalky, coiled or nicked. Sun and salt weaken mono.
- Braid: it lasts much longer. When the top section fades or frays, you can reverse it: wind it onto an empty spool, then back onto your reel so the fresh line is on top.
- After a big fish or a bad snag: check the first 20 to 50 metres and cut back if damaged.
Fixing line twist
If your line already twists, remove any lure, let out line behind a moving boat or a current for 30 to 50 metres, and wind back under tension. Avoid reeling while the drag is slipping, and close the bail by hand rather than by turning the handle; both habits cut twist dramatically.
Spooling a baitcasting or conventional reel
Revolving spool reels do not twist line, so direction matters less. Run the line through the level wind first, tie on with an arbor knot, and keep tension firm. Fill to just below the edge so the line does not rub the frame. Read our baitcasting and conventional reels guide for more.
Identify your catch with ReelScan: snap one photo to get the species, size and safety notes, and earn points. Scan a fish.
Fresh line, first fish
A newly spooled reel is the start of a new season of catches. When the first fish comes in, open ReelScan, take a real camera photo and see the species, size class and safety notes in seconds. Each catch you log earns points and helps you build a record of where and what you fish.
Summary
Open the bail, add backing under braid, tie on with an arbor or uni knot, check the line direction to avoid twist, wind on under firm, steady tension, and fill to 2 to 3 mm below the lip. Bed the line in on your first cast, re-spool mono yearly and reverse braid when it wears. Spool it right once and you will cast further and tangle less for the rest of the season. Next, choose the right saltwater spinning reel if you have not already.