Skills & gear › Hooks & tackle
Sinkers, Swivels and Terminal Tackle: The Saltwater Basics
Terminal tackle explained: sinker types and weights, swivels, snaps, split rings, beads and floats, and how they fit together in a rig.
Terminal tackle is everything at the business end of your line: sinkers, swivels, snaps, split rings, beads, floats, rig sleeves and hooks. These small, cheap parts decide whether your bait sits where the fish feed, whether your line twists, and whether your rig survives a powerful fish. This guide explains each piece, the most common fishing sinker types and weights, and how they fit together into the rigs sea anglers use every day.
Sinkers (weights)
A sinker takes your bait down and, in many rigs, holds it in place against waves and current. Choose shape for the job and weight for the conditions.
Common sinker types
- Pyramid sinker: the classic surf weight. Its flat sides and sharp edges dig into sand and hold against waves and current. The standard choice for the fish finder rig.
- Grip or spike sinker (breakaway): has wire arms that anchor in the sand in strong tides. Breakaway versions release the wires when you pull hard to retrieve.
- Bank sinker: a teardrop shape with an eye on top. Rolls less on hard bottoms and does not snag as much in rocks. Popular for bottom rigs from boats and piers.
- Egg and barrel sinkers: have a hole through the middle so line slides through. Used in sliding rigs where a fish can take the bait without feeling weight.
- Split shot: small balls pinched onto the line to add a little weight to a float rig or slow-sinking bait.
- Torpedo and trolling sinkers: streamlined shapes that take baits or lures down when trolling without spinning.
- Bell or dipsey sinkers: with a swivel moulded in, good for drifting rigs because they reduce twist.
How heavy should your sinker be?
Use the lightest weight that holds the bottom where you want it. Too light and your bait rolls out of the feeding zone; too heavy and fish feel it, you lose sensitivity and you snag more.
- Calm beach or harbour: 30 to 60 g (1 to 2 oz).
- Average surf: 85 to 140 g (3 to 5 oz).
- Strong tide or big surf: 150 to 200 g (5 to 7 oz) or grip leads.
- Boat bottom fishing in 20 to 50 m of water: 120 to 450 g (4 to 16 oz), depending on current and drift.
Make sure your rod's casting weight covers your sinker plus bait. See our surf fishing rod length guide.
Swivels
A swivel is a small metal connector that turns freely. It does two jobs: it joins main line to leader, and it stops line twist caused by spinning baits, lures and fish.
- Barrel swivel: the most common type. Use a black or dull finish in clear water.
- Ball bearing swivel: spins much more smoothly under load. Best for trolling and spinning lures.
- Three-way swivel: three rings, used to make simple bottom rigs with a sinker on one ring and a leader to the hook on another.
- Crane swivel: a strong, compact barrel swivel with a solid frame, popular for heavy bottom fishing.
Choose swivels rated at least as strong as your line. A weak swivel is a cheap way to lose a big fish.
Snaps and snap swivels
A snap is a safety-pin style clip that lets you change lures or sinkers quickly. Snap swivels combine a snap and a swivel. They are convenient but add weight and a possible weak point. Many lure anglers prefer to tie directly to the lure or use a small, strong split ring or a loop knot instead. Use snaps mainly for sinkers and quick rig changes.
Split rings and solid rings
Split rings join hooks to lures and assist hooks to jigs. Replace rusty or bent split rings on lures immediately; they are a common failure point on strong fish. Solid rings are welded closed and are used in jigging rigs to connect leader, jig and assist hooks.
Beads
Beads protect knots from sliding sinkers and add attraction. In a fish finder or sliding rig, a bead sits between the sinker slide and the swivel so the sinker does not crush your knot. Luminous and coloured beads also attract fish at night or in murky water.
Floats and bobbers
Floats suspend bait at a set depth and show bites when they move or sink. Use them for fishing over weed, around piers for mackerel and garfish, and for live bait drifting. Choose a float just big enough to support your bait and weight.
Rig components: sleeves, crimps and clips
- Crimps and sleeves: metal tubes squeezed onto heavy mono or wire to make strong connections where knots are impractical. Used in trolling and shark rigs.
- Bait clips and impact shields: used in surf casting to hold the bait close to the sinker during the cast for longer distance, then release it.
- Rig spools and wallets: keep pre-tied rigs tangle-free.
Putting it together: common rigs
- Fish finder rig: sliding sinker, bead, swivel, leader and circle hook. The classic surf rig. Step-by-step in how to tie a fish finder rig.
- Two-hook bottom rig (paternoster): sinker at the bottom, two hooks on dropper loops above it. Learn the dropper loop knot.
- Carolina or sliding egg rig: egg sinker above a swivel with a leader below, for working baits along the bottom.
- Float rig: float, split shot and hook for mid-water fishing.
Build a simple saltwater tackle box
A good starting kit: pyramid and bank sinkers in three weights, barrel and three-way swivels, a few snap swivels, beads, sinker slides, split rings, and hooks in several sizes and styles. Read types of fishing hooks and the fishing hook sizes chart to choose the hooks.
Keep terminal tackle fresh
Salt rusts small metal parts fast. Dry your tackle box after each trip, separate wet and dry items, and replace rusty swivels, snaps and rings. They are cheap; losing a fish is not.
Identify your catch with ReelScan: snap one photo to get the species, size and safety notes, and earn points. Scan a fish.
The rig is set, now find out what bites
Terminal tackle puts your bait in front of fish; ReelScan tells you exactly which fish found it. Photograph each catch with your camera to identify the species, check size and safety notes, and earn points for every real catch. Over time you will see which rigs catch which species on your local marks.
Summary
Choose sinker shape for the bottom and conditions and use the lightest weight that holds. Use quality swivels to join lines and prevent twist, beads to protect knots, and snaps mainly for sinkers. Keep a small kit of sinkers, swivels, rings and hooks, combine them into proven rigs, and replace anything rusty. Next, tie a fish finder rig.